HazMat Hazardous Material Storage Buildings

Hazardous Material Storage Building that is Specifically designed for hazardous / HAZMAT and flammable material storage and dispensing from 55-gallon drums containing flammable or combustible liquids. The Hazmat Storage Building Outer wall is constructed of all-welded 16 or 12 gauge steel. Inner wall is constructed of 20 gauge steel. The double wall construction contains 3" of air space throughout. All Flammable and Hazmat Storage Buildings are designed in accordance with the standards set forth by NFPA Code 30 and comply with OSHA and EPA regulations. All flammable models are FM Approved for the storing and dispensing of flammable and combustible liquids. Electrical installed in accordance with the NEC 2008 and 2011 editions and include UL Classified electrical accessories. Electrical Classification available at an additional charge. Please call for quote & options on your Hazmat building today. 

 Exterior Walls: (Models B200 through B1200) 16 gauge galvannealed steel.
* Building has double wall, welded construction, and 3” airspace throughout.
* Interior Walls: 20-gauge galvannealed steel.
* Exterior walls are 12-gauge galvanneal steel. Interior walls 20-guage cold roll.
* One 60” x 80” double door with a UL classified Commercial grade keyed lockset.
* Sump: 12-gauge steel liquid tight, continuously welded. 
* Heavy Gauge forklift channels with open-end construction.
* Grounding: OSHA Compliant Static ground connection inside and out on all explosion rated models 
* Labeling: NFR warning label, Hazard Ratings System, Instructions 
* Venting: Natural convection vents 
* Explosion Relief Panels: 22 gauge steel opening protected by expanded steel 
* Available with 2 or 4 hour fire rating 
* Chemical/corrosive/ultraviolet resisant paint 
* Removable galvanized steel safety floor planking
* Bolt-down plates (4) with 7/8” diameter holes for wind and seismic bracing.
* Multiple static grounding connections.
* Inlet vents for natural ventilation.
* Load Center is 120/240 Volt Single-Phase, NEMA 3R Rated (If needed, if no electrical options are ordered a load center will not be included).
* Explosion relief panels located in the rear wall of the building.
* Hazard labeling (DOT Placard Holder, NFPA 704 rating signs).
* Finish is a two-part chemical resistant aliphatic polyurethane. (Gray)
* Complies with NFPA Code 30.
* Building Factory Mutual approved, and UL listed accessories.
* Electrical installation UL classified and installed in accordance with the NEC 1999 and 2002 editions.

Slip resistant planking 13" wide, 12 gauge galvanized steel with raised perforated buttons and debossed holes protruding down. Galvanized steel floor planking above sump area for maximum corrosion resistance. Floor planking designed to sustain a minimum uniformly distributed load of 250 pounds per square foot. Floor planking and supports are removable to facilitate sump cleaning in the event of a spill.

Used in the construction of buildings designed to store Class IA and Class IB flammables. Explosion relief panels limit the damage within an enclosed hazardous location. When the panel(s) are subjected to an explosive force, the pressure relieving panel quickly vents the force before it causes major damage. The panels are designed to release at 20 psf.

Securall® Fire-Rated Hazardous Material Storage Buildings (10'H X 42'W X 9'D Max Dimensions) carry the Factory Mutual System Approval label and are constructed based upon UL Fire Resistance Ratings classification criteria. In addition, all Fire-Rated Buildings come with hydraulic operated self-closing, fire-rated doors and fire damper protected vents.

SECURALL® Buildings have been tested to determine the amount of force they can withstand and were shown to withstand F-4 tornado force winds of 250 mph. The chart below demonstrates the wind speed that a particular length of wall will resist.
Upgrade package is available for Tornado Resistant Walls.

Securall® Fire-Rated Storage Buildings (8'4"H X 42'W X 9'D Max Dimensions) carry the Factory Mutual System Approval label and have an FM Approved Fire Rated Wall & Roof Design. Wall and Roof are Tested at Intertek Testing Laboratories. Securall® Fire-Rated Storage Buildings constructed based upon UL Fire Resistance Ratings classification criteria. Standard models are available in 2-hour and 4-hour fire ratings. Wall ratings are either 2 or 4 hour fire rated . Roof ratings are either 1.5 or 3 hour fire rated (Check with your local authority having jurisdiction for correct wall/roof rating needed). In addition, all Fire-Rated Buildings come with hydraulic operated self-closing, fire-rated doors and fire damper protected vents.

If you need assistance, contact us at 1-800-474-7294 and speak to a storage building specialist.