Trowel or Brush on anti slip paint: Including permanent non skid coatings for indoor floor or outdoor uses. Helps provide slip resistance on concrete floor, wood, metal and more!
The ultimate in slip proof protection & chemical resistance. A 6 gallon pail containing resin, hardener and aggregate for the strongest possible bond and skid proofing on concrete, metal, fiberglass and more (just not tile).
To apply: Simply clean surface, mix up 2 part paint, roll down, broadcast the aggregate over it in a uniform fashion and let it dry 24 hours for foot traffic and 48 hours for vehicular. This 100% Epoxy Non Slip coating Kit can be used to help prevent accidents on sidewalks, ramps, trucks, production areas, driveways, basement floors, bricks and stones, steps and more. Excellent for use on floor areas which are subjected to abrasive traffic, impact and/or corrosive spillage. Easy to apply, yet tough enough to stand up to heavy vehicular traffic - even fork lift trucks.
This permanent non skid coating with its powerful industrial sand paper like finish saves down time by reducing slippery areas in any work environment even if wet or covered in liquids. (Epoxy Non Slip Coatings are Available in Clear, Black, Blue, Yellow as well as custom matched floor colors as close as possible.) Low odor and easy to clean for use indoors and outdoors on sidewalks, decks, walkways, floors, equipment and much more. ***Just a note-Please make sure "you want it where you apply it" as it is extremely difficult to remove once it dries. Call 1-800-474-7294 for ordering information and to go over the application in mind or click our contact form here.
Easy To apply!!! Produces a very hard and durable slip-resistant surface. This skid proof coating requires no mixing and makes a permanent non skid surface with just a roller or brush. Comes in a wide range of colors. For use to slip proof and accident prevention on sidewalks, ramps, trucks, production areas driveways, floors, steps, and more. Good for inside and concrete areas. Packed in 5 gallon pails and ready to use.
Any Questions, Please call us at 1-800-474-7294
AEROSOL SPRAY ON SLIP-RESISTANT EPOXY NON SLIP COATING
A super hard one part epoxy non slip coating that quickly cures to a slip resistant surface with a rough grit that is easy to use and requires no tools or mixing of chemicals to provide a safe non-skid surface. Aids in the reduction of slip and fall accidents. This unique aerosol contains special synthetic grit with no sharp edges. Available in several Non-Slip colors. Just spray it down on almost any hard surface except for rubber. May need to be re-applied as needed. Aerosol paint leaves surface like a diving board surface.
A slip-resistant, epoxy non slip coating that cures to a hard, flat, textured finish. Designed for interior and exterior use on concrete, steel, wood, fiberglass, aluminum and other surfaces where a slip-resistant finish is desired.
EFFECTIVE ON: Steps, ramps, loading docks, ladders, running boards, showers, around machinery or anywhere water or other slippery conditions exist.
SURFACE PREPARATION: The floor or surface applying should be dry, clean and free of oil, wax, dirt, loose paint and/or other contaminants. Previous areas that have paint already should be cleaned with a mild cleaner, rinsed and dried. Before initial non slip coating application to surface, a light etch or sanding is recommended. Test a small area for compatibility and adhesion. The coating is self-priming on most surfaces.
DRY TIME: Non Slip coating dries to touch in approximately one hour. Make sure first coat is dry before applying second coat. The rate of cure will vary with the film thickness, temperature and humidity. Wait 24 hours before subjecting to heavy foot traffic. Application will continue to cure for several days. Re-coat every 3 to 6 months depending on wear.
USE DIRECTIONS: For best results apply with ambient temperatures between 60°F to 90°F. Shake the paint can until ball rattles freely and then for an additional 60 seconds. Epoxy paint must be mixed well before and during use to achieve the correct color and texture. For best results shake can periodically during use. Spray non slip coating in a sweeping motion at a distance of 12 to 15 inches from area to
Three different non skid coatings to choose from